dot liner
Support information

• 
  Storng Adhesive
  TA- DM400-08N
• 
  Storng Adhesive (transparent)
  TA- DM400-08NT
• 
  Storng Adhesive (heart pattern)
  TA- DM405-08N
• 
  Apply strongly
  TA- DM403-08
• 
  Removable Adhesive
  TA- DM401-08

dot liner wide
Support information

• 
  Storng Adhesive
  TA- DM400-20N

• 
  Open the cap and secure it to the bottom of the main unit.
• 
  Glue will be transferred when you slowly pull it straight backwards.

• 
  Pinch the main unit in direction ❶ and pull it in direction ❷ to lift the refill tape.
• 
  Replace the refill tape, align it and push it in.
• 
  Hold the refill tape firmly and check that it locks with the main unit ❸.
• 
  After refilling, please remove the stopper before use.

• 
  If the tape becomes slack, stop gluing it.

[In case of small slack]

• 
  Place the tip of a pen or similar object into the groove and turn the core around which the glue is wrapped clockwise to take up any slack.

[In case of large sagging]

• 
  Leave the tape as is and pull it backwards while pinching the protrusions on both sides of the main unit.
• 
  Remove the refill tape straight out, being careful not to stick the tape to the main unit.
• 
  Flip the refill tape horizontally. While holding down the core on which the glue is wrapped, slowly turn the core on the side to be wound counterclockwise to remove any slack.
• 
  Make sure that the tape is taut and does not slack, then set the refill tape into the main unit.

dot liner hold
Support information

• 
  Storng Adhesive
  TA-

• 
  Insert the gluing part of the envelope all the way in so that it is parallel to the main body, and align the position where you want to start gluing with the ``glue from here'' arrow.
• 
  Glue can be done by lightly squeezing the lever, inserting the envelope, and slowly pulling the main unit toward you while holding the end of the envelope where you want to start gluing. When you want to finish applying the glue, release the lever and remove the envelope. *Please grip lightly as squeezing too hard may damage the paper.

• 
  Insert the paper all the way into the main unit and set it. When you repeatedly squeeze and release the lever, the roller rotates and the glue is automatically transferred to the paper.
  *Please be careful not to get the paper caught.

• 
  Insert the paper all the way into the main unit and set it. When you repeatedly squeeze and release the lever, the roller rotates and the glue is automatically transferred to the paper.
  *Please be careful not to get the paper caught.

• 
  ❶Press the ``PUSH button'' and lift it in the direction of ❷.
• 
  ❸Remove the refill tape.
• 
  ❹ Replace the refill tape, align it and keep pushing it in. ❺ Insert it securely into the main unit. ❻ Check the lock.

• 
  If the tape does not come out well, stop gluing for a moment.

• 
  Leave the tape as is and lift the main unit while pressing the "PUSH button" on the side of the main unit.
• 
  Remove the refill tape straight away.
• 
  Flip the refill tape horizontally. While holding down the core on which the glue is wrapped, slowly turn the core on the side to be wound counterclockwise to remove any slack.
• 
  Make sure that the tape is taut and does not slack, then set the refill tape into the main unit.

dot liner long 50
Support information

• 
  Storng Adhesive
  TA-

Open the cap and secure it to the bottom of the main unit.

Glue will be transferred when you slowly pull it straight backwards. At the end of the pull, lift it straight up.

• 
  ❶ Open the cap, ❷ while pressing the button on the top, open the ❸ cover.

• 
  Remove the used tape.
• 
  ❹After setting the new refill tape, ❺Close the cover firmly before use.

• 
  If the tape does not come out well, stop gluing for a moment.

• 
  Leave the tape as is and open the cover while pressing the "button" on the main unit.
• 
  Remove the refill tape straight out, being careful not to stick the tape to the main unit.
• 
  Flip the refill tape horizontally. While holding down the core on which the glue is wrapped, slowly turn the core on the side to be wound counterclockwise to remove any slack.
• 
  Make sure that the tape is taut and does not slack, then set the refill tape into the main unit.

dot liner long
Support information

• 
  Storng Adhesive
  TA-

• 
  Open the cap and secure it to the bottom of the main unit.
• 
  Place the tip on the area you want to paste and slowly pull it straight backwards to transfer the tape glue.

• 
  Fix the ❶ cap at the tip to the bottom of the main unit, press the ``PUSH button'' on the back of the ❷ main unit to release the lock, and remove the lock cover in the direction of ❸.
• 
  ❹ Lift up the top and bottom parts of the refill tape and ❺ remove it from the main unit.
• 
  Replace the refill tape, align it and push it in.
• 
  After refilling, put back the lock cover ❻ and then put back the cap ❼ at the tip.

• 
  If the tape does not come out well, stop gluing for a moment.

• 
  Leave the tape as is and open the lock cover while pressing the "PUSH button" on the back of the main unit.
• 
  Remove the refill tape straight out, being careful not to stick the tape to the main unit.
• 
  Flip the refill tape horizontally. While holding down the core on which the glue is wrapped, slowly turn the core on the side to be wound up clockwise to remove any slack.
• 
  Make sure that the tape is taut and does not slack, then set the refill tape into the main unit.

dot liner power
Support information

• 
  Attach super strongly
  TA- DM430-10N

• 
  Open the cap and secure it to the bottom of the main unit.
• 
  Place the tip on the area you want to paste and slowly pull it straight backwards to transfer the tape glue.
• 
  At the point where you want to cut, slowly lift the tip upwards in the direction of the arrow in the diagram.

• 
  Fix the ❶ cap at the tip to the bottom of the main unit, press the ``PUSH button'' on the back of the ❷ main unit to release the lock, and remove the lock cover in the direction of ❸.
• 
  ❹ Lift up the top and bottom parts of the refill tape and ❺ remove it from the main unit.
• 
  Replace the refill tape, align it and push it in.
• 
  After refilling, put back the lock cover ❻ and then put back the cap ❼ at the tip.

• 
  If the tape does not come out well, stop gluing for a moment.

• 
  Leave the tape as is and open the lock cover while pressing the ``PUSH button'' on the back of the unit.
• 
  Remove the refill tape straight out, being careful not to stick the tape to the main unit.
• 
  Flip the refill tape horizontally. While holding down the core on which the glue is wrapped, slowly turn the core on the side to be wound up clockwise to remove any slack.
• 
  Make sure that the tape is taut and does not slack, then set the refill tape into the main unit.

dot liner flick
Support information

• 
  Storng Adhesive
  TA- DM4900-06V/LB/W/B
• 
  Storng Adhesive (heart pattern)
  TA-
• 
  For printing/attaching later
  TA-

• 
  Push the back of the cap and rotate the cap 90 degrees to open it. The cap can be opened by rotating it to either the left or right.

• 
  Glue will be transferred when you slowly pull it straight backwards. At the end of the pull, lift it straight up.
• 
  Rotate the cap to close it.

• 
  ❶ Open the cap to the back of the illustration, and while pressing the ❷ up and down buttons, remove the cover in the direction of the ❸ arrow.

• 
  Remove the used tape and set a new refill tape.
• 
  Please use with the cover firmly attached.
  *If the cover is not completely attached, it may cause a malfunction.

• 
  If the tape becomes slack, stop gluing it.

• 
  Leave the tape as is and open the cover while pressing the "button" on the main unit.
• 
  Remove the refill tape straight out, being careful not to stick the tape to the main unit.
• 
  Flip the refill tape horizontally. While holding down the core on which the glue is wrapped, slowly turn the core on the side to be wound counterclockwise to remove any slack.
• 
  Make sure that the tape is taut and does not slack, then set the refill tape into the main unit.

dot liner compact
Support information

• 
  Storng Adhesive
  TA- DM4500-08NB
• 
  Storng Adhesive (heart pattern)
  TA- DM4550-08N
• 
  For printing/attaching later
  TA- DM4520-08NB
• 
  Removable Adhesive
  TA- DM4510-08N

products marked with a strikethrough line are no longer in production. Thank you for your patronage over the years.

• 
  Open the cap and secure it to the bottom of the main unit.
• 
  Glue will be transferred when you slowly pull it straight backwards.

• 
  While pressing the ❶ button, open the cover in the direction of ❷ and remove the used tape ❸.
• 
  ❹After setting a new refill tape, ❺replace the cover and use.

• 
  If the tape becomes slack, stop gluing it.

• 
  Leave the tape as is and open the cover while pressing the "button" on the main unit.
• 
  Remove the refill tape straight out, being careful not to stick the tape to the main unit.
• 
  Flip the refill tape horizontally. While holding down the core on which the glue is wrapped, slowly turn the core on the side to be wound counterclockwise to remove any slack.
• 
  Make sure that the tape is taut and does not slack, then set the refill tape into the main unit.

dot liner knock
Support information

• 
  Storng Adhesive
  TA- DM480-07NB/P

• 
  ❶Press the knock button ❷The cap will rotate and open.
• 
  Glue will be transferred when you slowly pull it straight backwards.

• 
  ❶ If the cap is open, press the knock button to close it. *It cannot be replaced if the tip is still exposed. ❷ While pressing the “OPEN” part of the cover, slide the cover in the direction of the arrow ❸ to remove it.
• 
  ❹ Pull the used tape straight up and remove it.
• 
  ❺Insert the new refill tape securely, ❻Put the cover over the main unit, and ❼slide to secure it to the main unit. If there is a gap at the tip, press ❽ to close the cover.

• 
  Turn the cap by hand in the direction of the arrow to release the lock.

• 
  If the tape becomes slack, stop gluing it.
• 
  Leave the tape in place and press the knock button to close the cap. Remove the cover by pressing the OPEN part of the cover and sliding it.

[In case of small slack]

• 
  Place the tip of a pen or similar object into the groove and turn the core around which the glue is wrapped clockwise to take up any slack.

[In case of large sagging]

• 
  Remove the refill tape straight out, being careful not to stick the tape to the main unit.
• 
  Flip the refill tape horizontally. While holding down the core on which the glue is wrapped, slowly turn the core on the side to be wound counterclockwise to remove any slack.
• 
  Make sure that the tape is taut and does not slack, then set the refill tape into the main unit.

dot liner stamp
Support information

• 
  Storng Adhesive
  TA- DM460-08

• 
  Grasp the main unit from above and place it vertically on the gluing area.
• 
  Align the position you want to glue with the projection on the tip of the cap.
• 
  If you press down slowly vertically as if stamping, you can glue it 600 times* with a size of approximately 8.4 x 10 mm (width x length). (The length may be reduced by approximately 1 to 2 mm.) *This is a design value and not a guaranteed value.

• 
  Open the cap.
• 
  Place the tip on the area you want to glue and pull it straight and slowly to transfer the tape glue.

• 
  Push "PUSH part" ❶ and open the cover in direction ❷.
• 
  ❸Open the cap and replace the refill tape. If the refill tape is floating, reinsert it again and make sure it is set securely.
• 
  ❹ Close the cap slowly and ❺ return the cover to use.

• 
  If the tape does not come out well, stop gluing for a moment.

• 
  Leave the tape as is and remove the cover by pressing the PUSH part of the main unit and sliding it.
• 
  Remove the refill tape straight away.
• 
  Flip the refill tape horizontally. While holding down the core on which the glue is wrapped, slowly turn the core on the side to be wound counterclockwise to remove any slack.
• 
  Remove the refill tape straight out, being careful not to stick the tape to the main unit.

dot liner fit
Support information

• 
  For printing/attaching later
  TA- DM490-07NB/P

This products is no longer in production. Thank you for your patronage over the years.

• 
  Open the cap and secure it to the bottom of the main unit.
• 
  Glue will be transferred when you slowly pull it straight backwards.

• 
  While pressing the ❶ button, open the cover in the direction of ❷ and remove the used tape ❸.
• 
  ❹After setting a new refill tape, ❺replace the cover and use.

• 
  If the tape becomes slack, stop gluing it.
• 
  Leave the tape as is and remove the cover by pressing the PUSH part of the main unit and sliding it.

[In case of small slack]

• 
  Place the tip of a pen or similar object into the groove and turn the core around which the glue is wrapped clockwise to take up any slack.

[In case of large sagging]

• 
  Remove the refill tape straight out, being careful not to stick the tape to the main unit.
• 
  Flip the refill tape horizontally. While holding down the core on which the glue is wrapped, slowly turn the core on the side to be wound counterclockwise to remove any slack.
• 
  Make sure that the tape is taut and does not slack, then set the refill tape into the main unit.

dot liner petite more
Support information

• 
  Storng Adhesive
  TA- D920-06LB/P
• 
  Storng Adhesive (heart pattern)
  TA- D927-06-1

• 
  Slide the slider in the direction of the arrow until it clicks into place.
• 
  Glue will be transferred when you slowly pull it straight backwards. At the end of the pull, lift it straight up.
• 
  When you finish using it, press the back of the slider and slide it in the direction of the arrow to close the cap.
  *Do not press the cap to close it.

• 
  If the tape becomes slack, stop gluing it.
• 
  Place the tip of a pen or similar object into the groove and turn the core around which the glue is wrapped clockwise to take up any slack.

dot liner small
Support information

• 
  Storng Adhesive
  TA- D930-06B

• 
  Slide the slider in the direction of the arrow until it clicks into place.
• 
  Glue will be transferred when you slowly pull it straight backwards. At the end of the pull, lift it straight up.
• 
  When you finish using it, press the back of the slider and slide it in the direction of the arrow to close the cap. *Do not press the cap to close it.

• 
  If the tape becomes slack, stop gluing it.
• 
  Place the tip of a pen or similar object into the groove and turn the core around which the glue is wrapped clockwise to take up any slack.

dot liner stick
Support information

• 
  Storng Adhesive
  TA- D900-06B/P

• 
  Remove the cap, place the tip on it and slowly pull it backwards.

• 
  Pull the tip in direction ❶ to remove the inner case.
• 
  Turn ❸ while holding ❷.